You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.
Thanksgiving: Support will not be available Thursday November 28th through Sunday December 1st. We will re-open Monday December 2nd.
Home > Image Play > [MaxColor] Image Pull via MJPEG Network Video Stream
[MaxColor] Image Pull via MJPEG Network Video Stream
print icon

Overview

Image Pull on MaxColor is a motion video that can be shown on a control system interface or web browser for an End User, while also being a powerful troubleshooting and diagnostic tool for the Installer.

Image Pull on MaxColor generates two types of video:

  1. an mJPEG video stream running at 720p and 30fps
  2. a higher quality snapshot of a single frame of video at 720p

MaxColor Transmitters and Receivers create a Motion-JPEG video stream viewable over the network - without audio - at up to 30 fps.


Access the Video Stream

To view the motion mJPEG video stream, go to the web address: http://[mc-ip]:8080/?action=stream. Replace [mc-ip] with the IP address of the Receiver or Transmitter to view.

For example, Receiver 1 video stream is http://172.27.1.1:8080/?action=stream

You can also view Image Pull in the webUI, on the Video Tab. View the video stream by enabling Auto Refresh button.


Access the Snapshot

To view the motion mJPEG video stream, go to the web address: http://[mc-ip]:8080/?action=stream. Replace [mc-ip] with the IP address of the Receiver or Transmitter to view.

For example, Receiver 1 video stream is http://172.27.1.1:8080/?action=stream

You can also view Image Pull in the webUI, on the Video Tab. The Snapshot is shown by default when the Auto Refresh button is disabled.


Defaults

The Motion-JPEG video stream has these settings by default:

  • Enabled: yes
  • Resolution: 640x360
  • Framerate: 30fps
  • 5 Mbps maximum bandwidth
  • Port: 8080

Settings

The command below applies the default settings listed above.

astparam s ss_stream_option 640,360,30,5000,0,10;astparam save;reboot

The default settings can be modified to alter the M-JPEG stream by sending the command via telnet or through the CLI of the Transmitter/Receiver with altered values. Any changes should be tested to confirm they do not interfere with HDMI video.

astparam s ss_stream_option $WIDTH,$HEIGHT,$FPS,5000,0,10;astparam save;reboot

Parameter Default Maximum Value<
$WIDTH 640 1280
$HEIGHT 360 720
$FPS 30 30

Examples:

  • astparam s ss_stream_option 1280,720,30,5000,0,10;astparam save;reboot
  • astparam s ss_stream_option 320,180,10,5000,0,10;astparam save;reboot

Troubleshooting

Image Pull is a useful troubleshooting tool for identifying where in the signal path the video signal stops. If you are familiar with 3G Ultra Image Pull, MaxColor works slightly differently.

Transmitter

On a Transmitter, Image Pull views the HDMI signal (this is the same as 3G Ultra). It shows you the video coming from the source, but does not tell you anything about the video signal on the network.

If a Transmitter (source) is showing black video, frozen video, jumpy video, or the signal is otherwise choppy or nonexistent when viewed on a display, we can use Image Pull to focus our troubleshooting efforts. Combine Transmitter and Receiver results based on the status of Image Pull in the webUI:

  1. when Image Pull is showing a clean video signal, then the HDMI signal is working correctly. The issue is on the network or on the Receiver side.
  2. when Image Pull is showing the same bad video that is on the display, then the HDMI connection is contributing to the issue. We can make no further determinations about the network or Receiver until we resolve the Transmitter HDMI issue.

Receiver

On a Receiver, Image Pull views the HDMI signal when the HDMI cable is connected to a display.
When the HDMI cable is NOT connected to a display, it shows the video signal from the network.
(This is different from 3G Ultra behavior).

If a Receiver (display) is showing black video, frozen video, jumpy video, or the signal is otherwise choppy or nonexistent, we can use Image Pull to focus our troubleshooting efforts. Perform these troubleshooting steps:

  1. With the Receiver HDMI DISconnected from an active display (meaning the HDMI is completely disconnected, or the display is not connected to power), Image Pull will show the network signal. If Image Pull is working, then the network is good. If Image Pull is not working as expected, the network signal is the cause of the issue.
  2. With the Receiver HDMI connected to an active display, Image Pull will ALWAYS show the same video as the display. If the display is black, Image Pull will be black.
  3. If the Receiver HDMI is connected to an active display and you need to check the network status, you must
    • disconnect the HDMI cable (or power off the display) so there is no active HDMI connection
    • THEN reboot the Receiver
    • (If you only disconnect the HDMI cable, the Receiver will be locked in the last state it was in while the HDMI was connected. It must reboot with the HDMI connected for the test to be valid.)
scroll to top icon