You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.
Thanksgiving: Support will not be available Thursday November 28th through Sunday December 1st. We will re-open Monday December 2nd.
Home > Network Management > Upload Switch Configuration File > Upload Switch Config to TP-Link TL-SG34XX Series
Upload Switch Config to TP-Link TL-SG34XX Series
print icon

Overview

Uploading a switch configuration file might be done for any of these reasons:

  • Copying the configuration from a defective switch into the replacement switch
  • Running AMP and loading the Discovery Configuration file

These instructions will fit any of these situations.


Minimum Switch Firmware

TP-Link switches have minimum firmware that must be loaded on the switch to be compatible with AMP systems. Please update switch firmware to the minimum version listed below:

Model Hardware Version Minimum Firmware Version
SG3428XMP 3.20 and 3.26 3.20.0
SG3452P 3.30 and 3.32 3.30.0
SG3452XP 2.20 and 2.26 2.20.1
TL-SG3428MP 1.x 1.1.7
2.x 2.0.11
4.x 4.0.6
5 and 5.6 5.0.4
5.2 and 5.26 5.0.4
6.0 6.0.2
TL-SG3428XF 1 and 1.60 1.0.3
TL-SG3428XMP 1.x 1.0.10
2 and 2.6 2.0.4
2.2 and 2.26 2.0.4
3 and 3.6 3.0.2
TL-SG3452P 1.x 1.1.7
2.x 2.0.5
3 3.0.4
3.20 and 3.26 3.20.4
TL-SG3452XP 1.x 1.0.4
2.x 2.0.1

*Yes, there is a difference between the switches with "TL-" at the front and the switches without it!


Identify Hardware Version

The minimum firmware version must be matched to the hardware version of the switch. There are 2 ways to find the hardware version of the switch:

  1. The label on the bottom of the switch shows the model number and the hardware version

    TP-Link Hardware Label

  2. The webUI lists the hardware version on the System --> System Info --> System Summary menu

    TP-Link webUI Hardware


Walkthrough

  1. Login to the switch webUI by going to the current IP address
    • Default IP is 192.168.0.1 /24 or DHCP on your network
    • Default username/password is admin/admin
    • Just Add Power config files use username/password: admin/tplink
  2. Check the firmware version on the switch to confirm it is at the minimum firmware version according to the table above.
  3. (Optional) To update firmware
    • Download the appropriate firmware from the TP-Link website. IMPORTANT: Firmware must match the Hardware Version of the switch. Each Hardware Version may have a different Firmware Version to upload, and uploading the wrong firmware could damage the switch!
    • Go to System Tools --> Firmware Upgrade and upload the firmware file. Be sure to check the box that says Reboot the switch using the backup image after upgrading is completed.

    • To run AMP, the switch must meet minimum firmware requirements.
  4. Once firmware is on a compatible version, go to System Tools --> Restore Config on the left menu.

  5. In the Configuration File field, click Browse and navigate to the configuration file.
  6. Check the box for Reboot the switch to validate the configuration after the restore is complete.
  7. Click Import to upload the new switch config.

  8. Done! The switch will reboot with the new config file uploaded.

Note: The Username/Password on an AMP VLAN Discovery Configuration file is admin/tplink


Troubleshooting: No Matrix Control

Symptoms

  1. Matrix Control through switching driver does not work, even though it is properly configured
  2. Standardized AMP functions do not work properly
    • Test Switching
    • Read System
    • Add Device On-Site
    • Edit Switch IP
    • Update Only

Cause

When AMP was run to setup the system, the TP-Link switch was not on minimum firmware.

Solution

  1. Update firmware on the switch to the minimum firmware.
  2. Then, re-upload the final switch configuration.
    • If you have the PC that ran AMP originally, open AMP and go to the top-left menu. Select File --> Open Projects Folder. Then navigate to the Project Name and Switch Configs. The file you need begins with jp. Use the webUI of the TP-Link switch to upload the jp file.
    • If you DO NOT have the PC that ran AMP originally, you will need to re-run Configure from the beginning to get the final switch configuration file.
scroll to top icon