Overview
JADConfig is no longer being updated. New systems should use AMP to configure systems, and should use the Choosing the Right Switch for AMP VLAN article to choose a switch.
When planning an installation, one of the most important decisions is the managed gigabit Ethernet switch that is the center of the Just Add Power matrix.
JADConfig will fully configure the switches listed below and Just Add Power provides drivers to support them.
*If the Right Switch is too large to fit on one switch or there are multiple switch locations, please see Multi-Switch Considerations for JADConfig for cable recommendations and bandwidth guidelines for systems with multiple switches.
Supported Switches
The switches listed in this section are supported by JADConfig and are currently being manufactured
Supported Switches: Luxul
| Model | Ports On | Max Devices | PoE Ports | Multi-Switch | Manufacturer Status |
|---|---|---|---|---|---|
| AMS-1208P | Rear | 9 | 7 | In Production | |
| AMS-1816P | Rear | 17 | 15 | In Production | |
| AMS-2600 | Rear | 25 | 0 | Discontinued Replace with AMS-2624P |
|
| AMS-2616P | Rear | 25 | 16 | Discontinued Replace with AMS-2624P |
|
| AMS-2624P | Rear | 25 | 23 | In Production | |
| AMS-4424P | Rear | 23 | 23 | Yes | Discontinued Replace with SW-610-24P-R Multi-switch system must change to AMP |
| XMS-1208P | Front | 9 | 7 | In Production | |
| XMS-2624P | Front | 25 | 23 | In Production | |
| XMS-5248P | Front | 47 | 47 | Discontinued Replace with SW-510-48P-F |
|
| XMS-7048P | Front | 47 | 47 | Yes | Discontinued Replace with SW-610-48P-F Multi-switch system must change to AMP |
| SW-510-48P-F | Front | 47 | 47 | In Production | |
| SW-610-24P-R | Rear | 23 | 23 | Must use AMP | In Production |
| SW-610-48P-F | Front | 47 | 47 | Must use AMP | In Production |
Switches listed as Discontinued are no longer made by the manufacturer, but are still supported by Just Add Power and JADConfig.
Supported Switches: Cisco
| Model | Ports On | Maximum Devices | PoE Ports | Multi-Switch | Status |
|---|---|---|---|---|---|
| CBS350-8P-2G | Front | 6 | 9 | In Production | |
| CBS350-8P-E-2G | Front | 6 | 9 | In Production | |
| CBS350-8FP-2G | Front | 8 | 9 | In Production | |
| CBS350-8FP-E-2G | Front | 8 | 9 | In Production | |
| CBS350-16P-2G | Front | 12 | 15 | In Production | |
| CBS350-16P-E-2G | Front | 12 | 15 | In Production | |
| CBS350-16FP-2G | Front | 15 | 15 | In Production | |
| CBS350-24P-4G | Front | 19 | 23 | In Production | |
| CBS350-24FP-4G | Front | 23 | 23 | In Production | |
| CBS350-48P-4G | Front | 37 | 47 | In Production | |
| CBS350-48FP-4G | Front | 47 | 47 | In Production | |
| SG300 | Front | 10/28/52 | 9/27/51 | Discontinued Replace with CBS350 |
|
| SG350 | Front | 10/28/52 | 9/27/51 | Discontinued Replace with CBS350 |
|
| SG500(X) | Front | 28/48/52 | 27/47/47 | Yes | Discontinued Replace with CBS350(-X) Multi-switch system must change to AMP |
| SG550X | Front | 28/48 | 27/47 | Yes | Discontinued Replace with CBS350(-X) Multi-switch system must change to AMP |
| The SG350X is not supported. For multi-switch systems, use the SG550X. | |||||
Switches listed as Discontinued are no longer made by the manufacturer, but are still supported by Just Add Power and JADConfig.
