You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.
Support will close at 3:00 pm Eastern on December 20th. Limited support will be available from 8:00 am to 6:00 pm on December 23rd, 26th, 27th, and 30th. Support will be closed December 24th, 25th, and 31st as well as New Year's Day.

Happy Holidays!
Home > Configuration Software > Advanced Matrix Programmer (AMP) > [Download] AMP: Configure a 3G Ultra or MaxColor System
[Download] AMP: Configure a 3G Ultra or MaxColor System
print icon

Overview

AMP - Advanced Matrix Programmer - configures 2G Omega, 3G Ultra or MaxColor devices into an HDMI matrix switching system.

AMP is the spiritual successor to JADConfig. If you were previously using JADConfig to configure 3G Ultra systems, you can continue to use it for maintaining those systems. However, we recommend that NEW systems should be configured with AMP.

There are two types of systems that can be configured by AMP:

  1. Standardized Configuration
    • AMP configures all Just Add Power devices AND the switch
    • Uses supported switches from this list.
    • Select Let's Go! to get started. 
    • Builds systems with up to 63 switches, 101 Transmitters, and 3023 Receivers
  2. Alternate Configuration
    • AMP configures all Just Add Power devices, and YOU are responsible for configuring the switch
    • The switch must be configured according to minimum requirements.
    • Select Alternate Configuration to get started.
    • Builds systems with up to 9,999 Transmitters and theoretically unlimited Receivers (based on network design).

Standardized Configuration is preferred. It essentially converts the switch into a video matrix switcher, with the added benefit of being able to use extra ports for data devices.

See Standard vs Alternate Configuration to determine which type of system is best for the job site.

Begin planning a MaxColor system here.

Begin planning a 3G Ultra system here.

Compare MaxColor and 3G Ultra here.


Download


Version Information

Current version: v1.2.2

Release Date: 2024-12-12

 


Standardized Configuration Supported Switches

In Standardized Configuration, the program configures the switch and all Just Add Power devices for you! AMP VLAN supports up to 63 switches in a system.

Standardized Configuration Supported Switch List


Alternate Configuration Switch Requirements

In Alternate Configuration, the switch must meet minimum requirements. You are responsible for configuring the switch; Just Add Power provides example profiles, but AMP does NOT configure the switch.


Just Add Power Firmware

3G: B3.0.1

MaxColor: MAX v4.1.2


Changelog

Added

  • Cisco Catalyst C1300 Series switches now supported
  • Check for an active TFTP server from another program and close it (other TFTP programs interfere with switch upload process when open)

Fixed

  • Cisco CBS350 8-port diagram port configuration
  • Netgear M4210PX discovery in model parsing
  • Add Device (Off-Site) firmware update timer was not showing
  • A6.x.x firmware was incorrectly being marked as "compatible" with B3.x.x firmware

Changed

  • Add Device (On-Site) redesigned to focus on firmware compatibility between new devices and system
  • Firmware Update Only redesigned to accompany the compatibility change to 
  • Mode set on devices based on Standard or Alternate mode
  • Clicking the 'X' button to close AMP restores video on devices before closing
  • Add Device (On-Site) reboots device after configuration
  • Luxul SW-XX5 models expand security timeout
  • Set Netgear aging-time to 300 seconds (was 3000 default)
  • TP-Link add IP interfaces for VLAN 131-201
  • Set Standard or Alternate mode on devices

Known Issues

[version] Issue

  • [1.0.0] WILL NOT auto-update to future versions. If you have v1.0.0, please download and install the latest version and it will auto-update going forward
scroll to top icon